SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:STATe?
Choices	Off \| On
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Power

Sets the power level, in dB for the selected channel.

Refer to the Output Power Calculation (Downlink) for a description of how the software applies to your power settings.
DL-SCH: Where the P_A parameter is set to a value in the range of -6 dB to 3 dB, the P_A parameter is enabled. When the P_A parameter is enabled, it takes priority over the Power parameter and so the Power cell is set 0 dB and is inactive.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:POWer <rel_ampl> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:POWer?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:POWer?
Range	-60 to 20 dB. When the P_A parameter is set to a value in the range of -6 dB to 3 dB, the P_A parameter is enabled. When the P_A parameter is enabled, it takes priority over the Power parameter and so the Power cell is set 0 dB and is read-only.
Dependencies	Inactive when P_A is set to a value other than Off.
Preset	0
State Saved	Yes
Min	-60
Max	20
Initial S/W Revision	A.20.01

P_A

Selects PDSCH relative power.
Where the P_A parameter is on (-6 dB to 3 dB), the P_A parameter takes priority over the Power parameter.
For more details, refer to 3GPP TS 36.213, and 36.331.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:PA OFF\|M6DB\|M4P77db\|M3DB\|M1P77db\|ZERodb\|P1DB\|P2DB\|P3DB [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:PA?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:PA ZERodb RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:PA?
Choices	Off \| -6 dB \| -4.77 dB \| -3 dB \| -1.77 dB \| 0 dB \| 1 dB \| 2 dB \| 3 dB. PDSCH relative power.
Dependencies	When P_A is set to a value (-6 dB to 3 dB), takes priority over Power parameter.
Preset	ZERodb
State Saved	Yes
Initial S/W Revision	A.20.01

UE Type

Selects UE Type for the corresponding DL-SCH.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:UE:TYPe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:UE:TYPe?
Choices	Non-BL/CE \| BL/CE
Preset	NBLCe
State Saved	Yes
Initial S/W Revision	A.20.01

UE Category

Sets UE Category for the corresponding DL-SCH.

The maximum number of supported layers for spatial multiplexing in DL is specified for each category.

The maximum transport block size determined by UE Category is checked during generation process.

See 3GPP TS 36.212 and 36.306 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:UE:CATegory CAT0\|CAT1\|CAT2\|CAT3\|CAT4\|CAT5\|CAT62l\|CAT64l\|CAT72l\|CAT74l\|CAT8\|CAT92l\|CAT94l\|CAT102l\|CAT104l\|CAT112l\|CAT114l\|CAT122l\|CAT124l\|CAT132l\|CAT134l\|CAT14\|CAT152l\|CAT154l\|CAT162l\|CAT164l\|CAT17\|CAT182l\|CAT184l\|CAT188l\|CAT192l\|CAT194l\|CAT198l\|CAT202l\|CAT204l\|CAT208l\|CAT212l\|CAT214l [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:UE:CATegory?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:UE:CATegory CAT14 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:UE:CATegory?
Notes	Non-BL/CE: 0 to 21 BL/CE: M1 (Fixed). The maximum number of supported layers for spatial multiplexing in DL is specified for each category respectively. The maximum transport block size determined by UE Category is checked during generation process.
Preset	CAT14
State Saved	Yes
Initial S/W Revision	A.20.01

Scrambling #0

Turns scrambling for PDSCH codeword on or off.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:SCRambling0 ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:SCRambling0?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:SCRambling0 ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:SCRambling0?
Choice	Off \| On
Dependencies	None.
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Scrambling #1

Turns scrambling for PDSCH codeword 1 on or off.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:SCRambling1 ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:SCRambling1?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:SCRambling1 ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:SCRambling1?
Choices	Off \| On
Dependencies	When UE Type is set to Non-BL/CE and Transmission Mode is 1, this setting is read-only.
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

RNTI Type

Selects RNTI type.
See 3GPP TS 36.321 7.1 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RNTi:TYPe C\|SI\|P\|RA [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RNTi:TYPe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RNTi:TYPe C RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RNTi:TYPe?
Choices	C-RNTI \| SI-RNTI \| P-RNTI \| RA-RNTI
Dependencies	Controls coupling of: Transmission Mode, Kmimo, Assigned Processes, RV Index Configuration, Number of HARQ Processes. When SI-RNTI: RV Config=Manual, Kmimo read-only, HARQ/Assigned Processes not applicable.
Preset	C
State Saved	Yes
Initial S/W Revision	A.20.01

RNTI

Sets the value, in decimal for the Radio Network Temporary Identifier (RNTI).

RNTI value and range depends on the RNTI Type.

RNTI is a generic term of an identifier for a UE.

RNTI = 0 to 65523 case, works for C-RNTI.

RNTI = 65535 case, works for SI-RNTI.

RNTI = 65534 case, works for P-RNTI.

For more details, refer to 3GPP TS 36.211, and 36.321.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RNTi?
Range	1 to 65523 (0xFFF3), 65535. RNTI = 0 to 65523 works for C-RNTI. RNTI = 65535 works for SI-RNTI and readonly. RNTI = 65534 works for P-RNTI and readonly. For RA-RNTI, it is 2400. Both decimal and hexadecimal entry formats are allowed.
Dependencies	RNTI value and range depends on the RNTI Type. Default follows DL-SCH channel number (DL-SCH#1 -> RNTI=1)
Preset	1
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

RNTI HEX

Query only

Displays hex representation of RNTI value. Both decimal and hexadecimal entry formats are allowed.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RNTi:HEX?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RNTi:HEX?
Dependencies	Automatically reflects RNTI decimal value in hex.
Preset	0x0001
State Saved	No
Initial S/W Revision	A.20.01

Transmission Mode

Sets the Transmission Mode for the corresponding DL-SCH.

1: Single Antenna Port (Port 0)
2: Transmit Diversity
3: Open-loop Spatial Multiplexing
4: Closed-loop Spatial Multiplexing
5: Multi-user MIMO
6: Closed-loop Spatial Multiplexing with Single Layer
7: Single Antenna Port (Port 5)
8: Single Antenna Port (Port 7 or 8)/Dual Layer Transmission (Ports 7 and 8)
9: Single Antenna Port (Port 7 or 8)/Up to 8 Layer Transmission (Ports 7 to 14)
10: Single Antenna Port (Port 7 or 8)/Up to 8 Layer Transmission (Ports 7 to 14)

When RNTI Type is set to P-RNTI, SI-RNTI or RA-RNTI, this setting is automatically set to:

1 (Single Antenna Port) for single antenna
2 (Transmit Diversity) for multi antenna

See 3GPP TS 36.212 and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TMODe TM1\|TM2\|TM3\|TM4\|TM5\|TM6\|TM7\|TM8\|TM9\|TM10 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TMODe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TMODe?
Choice	1\|7\|8\|9\|10 (single antenna) 2\|3\|4\|5\|6\|7\|8\|9\|10 (multi antenna) 8 not available with Extended CP. When PDCCH Allocations=4 with 1.4 MHz and Normal CP: TM7 not available.
Dependencies	When RNTI Type is P-RNTI, SI-RNTI or RA-RNTI, automatically set to 1 (single antenna) or 2 (multi antenna) and read-only.
Preset	TM1
State Saved	Yes
Initial S/W Revision	A.20.01

DM-RS

Demodulation Reference Signal (DM-RS) settings for DL-SCH. UE-Specific Reference Signal.

State

Turns the UE Specific Reference Signal state on or off.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:STATe OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:STATe?
Choices	Off \| On
Dependencies	Enabled when Transmission Mode is 7, 8, 9, or 10.
Preset	0
State Saved	Yes
Initial S/W Revision	A.20.01

Power

Sets the power level, in dB for the DM-RS.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:POWer <rel_ampl> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:POWer?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:POWer?
Dependencies	Active when DM-RS State is ON and Transmission Mode is 7, 8, 9 or 10.
Preset	0
State Saved	Yes
Min	-60
Max	20
Initial S/W Revision	A.20.01

Antenna Beam Configuration Mode

Sets the Antenna Beam Configuration Mode to degree or complex.

Degree: The antenna beam direction angle is set using degrees.
Complex: The antenna beam pattern is specified by a complex value.

This setting is applicable only when using a beam-forming transmission.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMconfig:MODe DEG\|COMP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMconfig:MODe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMconfig:MODe DEG RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMconfig:MODe?
Choice	Degree \| Complex
Dependencies
Preset	DEG
State Saved	Yes
Initial S/W Revision	A.20.01

Transmit Antenna Port

Selects the antenna port for the UE-Specific Reference Signal (DM-RS) transmission.
The choices available are dependent on Transmission Mode, Number of Antennas, and Number of Layers.
Coupling: This setting is active when UE-Specific Reference signal state (DM-RS) is On.
Refer to 3GPP TS 36.211, 36.212, and 36.213.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:TXAPort PORT5\|PORT7\|PORT8\|PORT78\|PORT79\|PORT710\|PORT711\|PORT712\|PORT713\|PORT714\|NA [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:TXAPort?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:TXAPort PORT78 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:TXAPort?
Notes	Sets the UE-Specific Reference Signal (DM-RS) transmit antenna port. Valid choices based on Transmission Mode and Total Number of Antennas: TM 7, any antennas : PORT5 TM 8, antennas <= 1 : PORT7, PORT8 TM 8, antennas >= 2 : PORT7, PORT8, PORT78 TM 9/10, antennas = 1 : PORT7, PORT8 TM 9/10, antennas = 2 : PORT7, PORT8, PORT78 TM 9/10, antennas <= 4 : PORT7-PORT710 TM 9/10, antennas <= 8 : PORT7-PORT714 TM 1-6 / DM-RS State Off : NA Range: PORT5 \| PORT7 \| PORT8 \| PORT78 \| PORT79 \| PORT710 \| PORT711 \| PORT712 \| PORT713 \| PORT714 \| NA
Dependencies	Active when DM-RS State is ON. Choices depend on Transmission Mode, Number of Antennas and Number of Layers.
Preset	NA
State Saved	No
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Antenna Beam for Port 5

Sets the antenna beam main lobe direction for DM-RS Port 5, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport5 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport5?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport5 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport5?
Dependencies	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, and Transmit Antenna Port includes Port 5. When set, the Transmit Antenna Weight for Port 5 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 8

Sets the antenna beam main lobe direction for DM-RS Port 8, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport8 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport8?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport8 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport8?
Dependencies	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 8 and Transmit Antenna Port is Port 8, and Transmit Antenna Port includes Port 8. When set, the Transmit Antenna Weight for Port 8 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 9

Sets the antenna beam main lobe direction for DM-RS Port 9, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport9 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport9?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport9 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport9?
Dependencies	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-9, Total number of antennas is 4 Antennas. When set, the Transmit Antenna Weight for Port 9 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 10

Sets the antenna beam main lobe direction for DM-RS Port 10, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport10 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport10?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport10 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport10?
Notes	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-10, Total number of antennas is 4 Antennas and Transmit Antenna Port includes Port 10. When set, the Transmit Antenna Weight for Port 10 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 11

Sets the antenna beam main lobe direction for DM-RS Port 11, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport11 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport11?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport11 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport11?
Dependencies	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-11, Total number of antennas is 8 Antennas. When set, the Transmit Antenna Weight for Port 11 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 12

Sets the antenna beam main lobe direction for DM-RS Port 12, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport12 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport12?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport12 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport12?
Dependencies	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-12, Total number of antennas is 8 Antennas When set, the Transmit Antenna Weight for Port 12 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 13

Sets the antenna beam main lobe direction for DM-RS Port 13, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport13 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport13?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport13 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport13?
Notes	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-13, Total number of antennas is 8 Antennas When set, the Transmit Antenna Weight for Port 13 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Antenna Beam for Port 14

Sets the antenna beam main lobe direction for DM-RS Port 14, in degrees.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport14 <angle> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:BEAMport14?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport14 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:BEAMport14?
Notes	Visible when Antenna Beam Configuration Mode = Degree, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-14, Total number of antennas is 8 Antennas When set, the Transmit Antenna Weight for Port 14 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	0
Min	-90
Max	90
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 5

Sets the transmit antenna weight for DM-RS Port 5 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to the Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport5 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport5?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport5 "1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport5?
Dependencies	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 7, Transmit Antenna Port is Port 5, Total number of antennas is 1 Antennas When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1" when total number of antennas is 1. "1,1" when total number of antennas is 2. "1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8.
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 7

Sets the transmit antenna weight for DM-RS Port 7 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to the Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport7 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport7?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport7 "1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport7?
Dependencies	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 8, Transmit Antenna Port is Port 7, Total number of antennas is 2 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1" when total number of antennas is 2. "1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8.
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 8

Sets the transmit antenna weight for DM-RS Port 8 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to the Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport8 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport8?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport8 "1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport8?
Notes	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 8, Transmit Antenna Port is Port 8, Total number of antennas is 4 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8.
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 9

Sets the transmit antenna weight for DM-RS Port 9 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to the Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport9 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport9?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport9 "1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport9?
Notes	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-9, Total number of antennas is 4 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8.
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 10

Sets the transmit antenna weight for DM-RS Port 10 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j");

The count must be equal to Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport10 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport10?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport10 "1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport10?
Notes	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-10, Total number of antennas is 4 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8.
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 11

Sets the transmit antenna weight for DM-RS Port 11 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport11 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport11?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport11 "1,1,1,1,1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport11?
Notes	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-11, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1,1,1,1,1"
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 12

Sets the transmit antenna weight for DM-RS Port 12 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport12 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport12?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport12 "1,1,1,1,1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport12?
Dependencies	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-12, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1,1,1,1,1"
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 13

Sets the transmit antenna weight for DM-RS Port 13 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport13 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport13?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport13 "1,1,1,1,1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport13?
Dependencies	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-13, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1,1,1,1,1"
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmit Antenna Weight for Port 14

Sets the transmit antenna weight for DM-RS Port 14 as a complex value string (e.g. "1.0+0.0j").

For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").

The count must be equal to Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport14 <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DMRS:WEIGhtport14?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport14 "1,1,1,1,1,1,1,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DMRS:WEIGhtport14?
Notes	Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-14, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211.
State Saved	Yes
Preset	"1,1,1,1,1,1,1,1"
Range	Complex number string, e.g. "1.0+0.0j", or comma-separated list per antenna
Initial S/W Revision	A.20.01

Transmission Settings

DL-SCH transmission configuration settings.

Coding State

This setting applies to the DCI, BCH, and DL-SCH channels.
Turns the coding state On or Off.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:CODing:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:CODing:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:CODing:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:CODing:STATe?
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Kmimo

Query only

See 3GPP TS 36.212 for more information about the Kmimo parameter.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:KMIMo?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:KMIMo?
Range	When Transmission Mode is 3 or 4, Kmimo = 2 Otherwise = 1
Dependencies	When RNTI = 65535 (SI-RNTI), Kmimo is read-only and not applicable.
Preset	1
State Saved	Yes
Min	1
Max	2
Initial S/W Revision	A.20.01

Data #1

This setting applies to DL-SCH channels.

Selects PN9, PN15, or User Defined Bits to use for the data in transport block 1. Click the > button displayed with the setting to make the value selection.

For more details, refer to 3GPP TS 36.211, and 36.212.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa1 PN9\|PN15\|PN23 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa1?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa1 PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa1?
Preset	PN9
State Saved	Yes
Initial S/W Revision	A.20.01

Data #1 User Defined

This setting applies to DL-SCH channels. Sets User Defined Bits to use for the data in transport block 1.

For more details, refer to 3GPP TS 36.211, and 36.212.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa1:USER<string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa1:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa1:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa1:USER?
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Data #2

This setting applies to DL-SCH channels. Selects PN9, PN15, or User Defined Bits to use for the data in transport block 2. Click the > button displayed with this setting to make the value selection.

For more details, refer to 3GPP TS 36.211, and 36.212.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa2 PN9\|PN15\|PN23 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa2?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa2 PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa2?
Preset	PN9
State Saved	Yes
Initial S/W Revision	A.20.01

Data #2 User Defined

This setting applies to DL-SCH channels. Sets User Defined Bits to use for the data in transport block 2.
For more details, refer to 3GPP TS 36.211 and 36.212.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa2:USER<string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DATa2:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa2:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DATa2:USER?
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Modulation and TBS Index Table

Selects Modulation and TBS Index Table for PDSCH.

See 3GPP TS 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:MOD:TBS:TABLe TAB1\|TAB2\|TAB3\|TAB4 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:MOD:TBS:TABLe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:MOD:TBS:TABLe TAB1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:MOD:TBS:TABLe?
Choices	Table 1 \| Table 2 \| Table 3 \| Table 4 Table 1: QPSK/16QAM/64QAM (36.213 7.1.7.1-1) Table 2: +256QAM (7.1.7.1-1A) Table 3: +1024QAM (7.1.7.1-1B) Table 4: +1024QAM (7.1.7.1-1C)
Dependencies	Visible only when UE Type = Non-BL/CE. With the table selection, there is a relationship between DL-SCH Tx sequence: MCS #1/2, Mod #1/2, TBS #1/2.
Preset	TAB1
State Saved	Yes
Initial S/W Revision	A.20.01

TBS Index Alt

Selects TBS Index Alt.

See 3GPP TS 36.213 7.1.7 and 36.331 6.3.2 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TBS:ALT NONe\|A26\|A33 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TBS:ALT?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TBS:ALT NONe RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TBS:ALT?
Choices	None \| 26A \| 33A None and 26A are available when: Mod/TBS Table=Table 1, TM=9 or 10, DM-RS State=On. None and 33A are available when: Mod/TBS Table=Table 2 or 3, TM=9 or 10, DM-RS State=On. Otherwise None is available and setting is read-only.
Dependencies	Visible only when UE Type = Non-BL/CE. Requires TM 9/10 + DM-RS ON. Table 1: 26A available. Table 2/3: 33A available. Otherwise read-only (None).
Preset	NON
State Saved	Yes
Initial S/W Revision	A.20.01

TBS Index Alt2

Selects TBS Index Alt2.

See 3GPP TS 36.213 7.1.7 and 36.331 6.3.2 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TBS:ALT2 NONe\|B33 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TBS:ALT2?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TBS:ALT2 NONe RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TBS:ALT2?
Choices	None \| 33B None and 33B available when: Mod/TBS Table=Table 2, 3 or 4, TM=1, 2, 3, 4, 6 or 7. Otherwise None is available and setting is read-only.
Dependencies	Visible only when UE Type = Non-BL/CE. Requires Mod/TBS Table 2/3/4 + TM 1/2/3/4/6/7. Otherwise read-only (None).
Preset	NONe
State Saved	Yes
Initial S/W Revision	A.20.01

TBS Index Alt3

Selects TBS Index Alt3.

See 3GPP TS 36.213 7.1.7 and 36.331 6.3.2 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TBS:ALT3 NONe\|A37 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TBS:ALT3?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TBS:ALT3 NONe RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TBS:ALT3?
Choices	None \| 37A None and 37A are available when Modulation and TBS Index Table is Table 3. Otherwise None is available and setting is read-only.
Dependencies	Visible only when UE Type = Non-BL/CE. Available only when Mod/TBS Table = Table 3. Otherwise read-only (None).
Preset	NONe
State Saved	Yes
Initial S/W Revision	A.20.01

RV Index Configuration

Sets the RV Index Configuration for the selected DL-SCH.
If set to Auto, then RV Index Sequence is active.
Where RNTI = 65535 (SI-RNTI) this parameter is set to Manual.
If set to Manual, then RV Index Sequence is inactive.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RV:CONFig AUTo\|MAN [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RV:CONFig?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RV:CONFig AUTo RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RV:CONFig?
Choices	Auto \| Manual If Auto, RV Index Sequence is active. If Retrans in DL-SCH Tx sequence is On, next RV Index in sequence is used.
Couplings	When RNTI = 65535 (SI-RNTI), this parameter is set to Manual.
Dependencies	Controls active state of RV Index Sequence. Forced to Manual when RNTI Type = SI-RNTI.
Preset	AUTo
State Saved	Yes
Initial S/W Revision	A.20.01

RV Index Sequence

This setting applies only to DL-SCH.
Sets the numbers of individual RV Index Sequence, separated by commas (for example, 1,2,3).

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RV:SEQuence <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:RV:SEQuence?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RV:SEQuence "0,2,3,1" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:RV:SEQuence?
Range	Range of sequence length: 1 to 16. Range of each value: 0 to 3. If Retrans in DL-SCH Tx sequence=On, next RV Index is used.
Dependencies	Active when RV Index Configuration = Auto. Inactive/read-only when RNTI = 65535 (SI-RNTI) or RV Config = Manual.
Preset	"0, 2, 3, 1"
State Saved	Yes
Initial S/W Revision	A.20.01

Number of HARQ Processes

This setting applies only to DL-SCH channels.
The value sets the number of available HARQ processes and defines the interval between retransmissions.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:HARQ:NPRocesses <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:HARQ:NPRocesses?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:HARQ:NPRocesses 8 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:HARQ:NPRocesses?
Range	1 to 8 Where RNTI = 65535 (SI-RNTI) this is not applicable and read-only. Otherwise settable.
Dependencies	Defines the interval between retransmissions. Use Assigned Processes to enable HARQ processes. Read-only when RNTI Type = SI-RNTI.
Preset	8
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Assigned Processes

This setting applies only to DL-SCH channels.
Sets the numbers of individual HARQ processes, separated by commas (e.g., 1,2,3) or a range (e.g., 1-3).

Where RNTI = 65535 (SI-RNTI) this parameter is not applicable and read only.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:HARQ:ASSigned <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:HARQ:ASSigned?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:HARQ:ASSigned "0-7" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:HARQ:ASSigned?
Range	0 to (Number of HARQ Processes - 1).
Dependencies	Where RNTI = 65535 (SI-RNTI), this setting is not applicable and read-only. Number of available HARQ processes defined in Number of HARQ Processes.
Preset	"0-7"
State Saved	Yes
Initial S/W Revision	A.20.01

Transmission Configuration Length

Sets the length of transmission configuration. The definition of transmission configuration of SCH and related DCI will be repeated to the end of the Waveform Generation Length.

Transmission Configuration Length <= Waveform Generation Length.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TRAN:CONFig:LENGth <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TRAN:CONFig:LENGth?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TRAN:CONFig:LENGth 40 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TRAN:CONFig:LENGth?
Range	10 ms to Waveform Generation Length Max 160 ms. Value available to set 1-16 Frames. Transmission Configuration Length <= Waveform Generation Length. DCI 1-8 auto-set to same value as corresponding DL-SCH. Configuration is repeated to end of Waveform Generation Length.
Dependencies	If Waveform Generation Length is set less than Transmission Configuration Length, value is changed to <= Waveform Generation Length. DCI 1-8 auto-set to same value.
Preset	40
State Saved	Yes
Min	10
Max	Waveform Generation length value
Initial S/W Revision	A.20.01

DCI # 1/ PDCCH

DCI control settings for this DL-SCH instance.

DCI State

Turns the channel On or Off.
DCI #1 corresponds with DL-SCH #1, DCI #2 corresponds with DL-SCH #2, and so on.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:STATe?
Choices	Off \| On
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

DCI Data

Query only

This setting applies to DCI channels. DCI #1 corresponds with DL-SCH #1, DCI #2 corresponds with DL-SCH #2, and so on.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:DATa?
Coupling	Automatically linked to corresponding DL-SCH channel.
Preset	DL-SCH1
State Saved	No
Initial S/W Revision	A.20.01

Search Space Auto-Assignment

Enables or disables the Search Space Auto-Assignment parameter.

See 3GPP TS 36.213 and 36.331.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:SEARchspace:AUTo ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:SEARchspace:AUTo?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:SEARchspace:AUTo ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:SEARchspace:AUTo?
Choices	Off \| On
Dependencies	When ON, Candidate values in DCI TX are automatically assigned from unused lower number.
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Transmission Configuration

Per-subframe PDSCH transmission settings.

Up to 40 sequences (4 frames x 10 subframes).

State

Enables or disables this PDSCH TX sequence.

Per-subframe setting (seq 1-40, 4 frames x 10 subframes).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:STATe?
Choices	On \| Off
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Precoding

Selects the precoding method applied to the PDSCH Tx sequence.

OFF: No precoding (single antenna port, TM 1 or TM 7).
TDIV: Transmit Diversity - space-frequency block coding across antenna ports (TM 2).
SMUL: Spatial Multiplexing - multiple independent data streams across layers (TM 3/TM 4).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

See 3GPP TS 36.211 and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<n>:PRECoding?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:PRECoding?
Notes
Dependencies	This setting is visible when: State is ON. Total Number of Antennas is greater than 1. Linked to Transmission Mode: TM 1/7 -> OFF, TM 2 -> TDIV, TM 3/4/8-10 -> SMUL. Affects # Layers and # Codewords. SCPI values: OFF \| TDIV \| SMUL.
Preset	OFF
State Saved	Yes
Initial S/W Revision	A.20.01

# Layers

Sets the number of spatial multiplexing layers for the PDSCH Tx sequence. Each layer carries an independently coded data stream. The maximum number of layers is limited by UE Category and Transmission Mode.

See 3GPP TS 36.211, 36.212 and 36.213 for more information.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<n>:NLAYers?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:NLAYers?
Dependencies	This setting is visible when: State is ON. Total Number of Antennas is greater than 1. Transmission Mode: TM 3 (Open-loop SM), TM 4 (Closed-loop SM), TM 8-10 support multiple layers. Maximum layers constrained by UE Category. Related to Precoding and # Codewords settings.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

# Codewords

Sets the number of codewords (transport blocks) for the PDSCH Tx sequence.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<n>:NCODewords?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:NCODewords?
Notes	Sets the number of codewords (transport blocks) for the PDSCH Tx sequence. 1: Single transport block. Parameters MCS #2, Mod #2, and TBS #2 are not visible. 2: Dual transport block (spatial multiplexing). Both codewords are independently encoded. See 3GPP TS 36.211, 36.212 and 36.213 for more information. (This setting is not visible when state is OFF) This setting is visible when total number of antennas is greater than 1
Dependencies	When set to 1, parameters MCS #2, Mod #2, and TBS #2 are not visible. Spatial multiplexing (TM 3, TM 4) supports up to 2 codewords. Related to # Layers and Precoding settings.
Preset	1
State Saved	Yes
Min	1
Max	2
Initial S/W Revision	A.20.01

Retrans #1

Sets the re-transmission process of transport block 1 (codeword 0) for the corresponding PDSCH transmission.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<n>:RETRans:ONE OFF\|ON\|0\|1 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<n>:RETRans:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RETRans:ONE OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RETRans:ONE?
Notes	Sets the re-transmission process of transport block 1 (codeword 0) for the corresponding PDSCH transmission. ON: Re-transmission data with next RV index is transmitted; the new data indicator is not toggled. OFF: New data is transmitted; the new data indicator is toggled. Note: First transmission of each HARQ process cannot be set to re-transmission. This parameter appears only when UE Type is set to Non-BL/CE. See 3GPP TS 36.212 and 36.213 for more information. (This Setting will be visible from Seq 9 onwards in Transmission Configuration in DL-SCH node) (This setting is not visible when state is OFF) This setting is visible when total number of antennas is greater than 1
Dependencies	UE Type = Non-BL/CE. Read-only for first transmission in each HARQ process.
Preset	OFF
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

MCS #1

Selects the value to set the MCS index for codeword 1.
The MCS index defines the modulation order and TBS index.
When the MCS Index is Off (-1), the Modulation and TBS Index are active and can be user-defined.
For more information, refer to 3GPP TS 36.212 and 36.331.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:MCS:ONE <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:MCS:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:MCS:ONE 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:MCS:ONE?
Notes	MCS Index = Off (-1): Modulation and TBS Index are settable by user. MCS Index = 0 to 31 (or higher per table): Modulation and TBS Index are automatically set by software. With MCS set to a value, Mod and TBS auto-set.
Dependencies	This setting is not visible when state is OFF. When MCS Index set to a value (not Off), Mod #1 and TBS #1 are read-only and auto-set by software.
Preset	0
State Saved	Yes
Min	-1
Max	31
Initial S/W Revision	A.20.01

Mod #1

Query only

Displays the modulation type for codeword 1. Derived from MCS.
Coupling: Read only and set by the software until MCS Index is set to Off.
Refer to 3GPP TS 36.213.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:MODulation:ONE QPSK\|QAM16\|QAM64 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:MODulation:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:MODulation:ONE QPSK RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:MODulation:ONE?
Notes	Modulation is automatically set by software when MCS Index has a value. Settable when MCS Index = Off.
Dependencies	Read-only and set by software until MCS Index is set to Off. (This setting is not visible when state is OFF)
Preset	QPSK
State Saved	No
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

TBS #1

Query only

Displays the TBS Index for codeword 1. Read-only, derived from MCS.
Coupling: Read only and set by the software until MCS Index is set to Off.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:TBS:INDex:ONE OFF\|TBS0\|TBS1\|TBS2\|TBS3\|TBS4\|TBS5\|TBS6\|TBS7\|TBS8\|TBS9\|TBS10\|TBS11\|TBS12\|TBS13\|TBS14\|TBS15\|TBS16\|TBS17\|TBS18\|TBS19\|TBS20\|TBS21\|TBS22\|TBS23\|TBS24\|TBS25\|TBS26\|TBS26a [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:TBS:INDex:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:TBS:INDex:ONE TBS0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:TBS:INDex:ONE?
Notes	TBS Index is automatically set by software when MCS Index has a value. Settable when MCS Index = Off.
Dependencies	This setting is not visible when state is OFF. Read-only and set by software until MCS Index is set to Off.
Preset	TBS0
State Saved	No
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

TB Size #1

Query Only

Displays the Transport Block Size for codeword 1.
Coupling: Read only and set by the software until TBS Index is set to Off.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh:TX:TBSize:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:TBSize:ONE?
Notes	Automatically calculated from TBS Index and RB allocation. When TBS Index = Off, TB Size is settable by user.
Dependencies	This setting is not visible when state is OFF. Read-only when TBS Index has a value. Editable when TBS Index = Off.
Preset	1384
State Saved	No
Min	1
Max	97896
Initial S/W Revision	A.20.01

RV #1

Sets the Redundancy Version for codeword 1.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RV:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RV:ONE?
Range	0 to 3
Dependencies	This setting is not visible when state is OFF. When RV Index Configuration = Auto and Retrans = On, auto-set from RV Index Sequence.
Preset	0
State Saved	Yes
Min	0
Max	3
Initial S/W Revision	A.20.01

RA Type

Sets the Resource Allocation type for PDSCH.

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RATYpe TYPe0\|TYPe1\|TYPe2 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RATYpe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RATYpe TYPe2 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RATYpe?
Choices	Type 0 \| Type 1 \| Type 2
Dependencies	This setting is not visible when state is OFF.
Preset	TYPe2
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Subset

Sets the subset number (for RA Type 1).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:SUBSet <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:SUBSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:SUBSet 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:SUBSet?
Range	0 to 2
Dependencies	This setting is not visible when state is OFF. Active when RA Type = Type 1.
Preset	0
State Saved	Yes
Min	0
Max	2
Initial S/W Revision	A.20.01

Shift

Enables or disables shift (for RA Type 1).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:SHIFt ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:SHIFt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:SHIFt OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:SHIFt?
Choice	On \| Off
Dependencies	Active when RA Type = Type 1. This setting is not visible when state is OFF.
Preset	0
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

RBG Bitmap

Sets the RBG bitmap (for RA Type 0).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RBG:BITMap:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RBG:BITMap:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RBG:BITMap:USER "11111111111111" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RBG:BITMap:USER?
Notes	Binary string of 0s and 1s. Length depends on System Bandwidth.
Dependencies	This setting is not visible when state is OFF. Active when RA Type = Type 0\| Type 1.
Preset	"1111111111111"
State Saved	Yes
Initial S/W Revision	A.20.01

VRB Type

Sets the VRB type (for RA Type 2).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:VRBType LOC\|DIST [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:VRBType?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:VRBType LOC RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:VRBType?
Choices	Localized \| Distributed
Dependencies	This setting is not visible when state is OFF. Active when RA Type = Type 2.
Preset	LOC
State Saved	Yes
Initial S/W Revision	A.20.01

RB Offset

Sets the RB offset (for RA Type 2).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RB:OFFSet <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RB:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RB:OFFSet 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RB:OFFSet?
Notes	Range: 0 to 99 (depends on System Bandwidth). When Signal Bandwidth is 1.4 MHz= RB Size max is 5 When Signal Bandwidth is 3 MHz= RB Size max is 14 When Signal Bandwidth is 5 MHz= RB Size max is 24 When Signal Bandwidth is 10 MHz= RB Size max is 49 When Signal Bandwidth is 15 MHz= RB Size max is 74 When Signal Bandwidth is 20 MHz= RB Size max is 99
Dependencies	This setting is not visible when state is OFF. Enabled when RA Type = Type 2.
Preset	0
State Saved	Yes
Min	0
Max	99
Initial S/W Revision	A.20.01

RB Size

Sets the number of resource blocks (for RA Type 2).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:TX<seq>:RB:NUMBer <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSC<n>:TX<seq>:RB:NUMBer?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RB:NUMBer 50 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RB:NUMBer?
Notes	Range: 1 to 100 (depends on System Bandwidth). When Signal Bandwidth is 1.4 MHz= RB Size max is 6 When Signal Bandwidth is 3 MHz= RB Size max is 15 When Signal Bandwidth is 5 MHz= RB Size max is 25 When Signal Bandwidth is 10 MHz= RB Size max is 50 When Signal Bandwidth is 15 MHz= RB Size max is 75 When Signal Bandwidth is 20 MHz= RB Size max is 100
Dependencies	This setting is not visible when state is OFF. Active when RA Type = Type 2.
Preset	50
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RB Gap

Sets the RB gap value (for distributed VRB).

Per-subframe setting (seq 1-n, where n is the value of Transmission Configuration Length).

n is from 0-7

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSC<n>:TX<seq>:RB:GAP NGAP1\|NGAP2 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSC<n>:TX<seq>:RB:GAP?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RB:GAP NGAP1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RB:GAP?
Choices	Ngap 1 \| Ngap 2
Dependencies	This setting is not visible when state is OFF. Enabled when RA Type = Type 2 and VRB Type = Distributed.
Preset	NGAP1
State Saved	Yes
Initial S/W Revision	A.20.01

DCI #1 (DL-SCH Control)

DCI #1 PDCCH Transmission Configuration for DL-SCH1.

Up to 40 sequences (4 frames x 10 subframes).

State

Enables or disables this DCI TX sequence.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:STATe?
Notes	Choice: On \| Off. Where the data is set to Auto-Configured Bits, this parameter is read only and automatically defined by corresponding DL-SCH. Otherwise settable by user.
Dependencies	Read-only when Data = Auto-Configured Bits.
Preset	0
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Format

Set the DCI format for this PDCCH transmission.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:FORMat?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:FORMat?
Notes	This parameter indicates DCI Format type to the corresponding DL-SCH. Automatically selected by DL-SCH and system settings. Refer to 3GPP TS 36.211, 36.212, 36.213. (This setting is not visible when state is OFF)
Dependencies	Automatically selected by DL-SCH and system settings.
Preset	F1A
State Saved	Yes
Initial S/W Revision	A.20.01

TPC PUCCH

Sets the TPC command for PUCCH.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:TPCPucch TPC0\|TPC1\|TPC2\|TPC3 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:TPCPucch?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:TPCPucch TPC0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:TPCPucch?
Notes	Use the drop-down menu to select the UE's accumulative Tx Power Control (TPC) PUCCH power step.
Dependencies	This setting is not visible when state is OFF.
Preset	TPC0
State Saved	Yes
Initial S/W Revision	A.20.01

SRS Request

Sets the SRS Request value.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:SRS:REQuest <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:SRS:REQuest?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:SRS:REQuest 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:SRS:REQuest?
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

Data

Sets the DCI payload data for this PDCCH transmission.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:DATA PN9\|PN15\|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:DATA?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:1:DCI:TX:DATA PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:1:DCI:TX:DATA?
Choices	PN9 \| PN15 \| Auto-Configured Bits Where Auto-Configured Bits, DCI data contents contain corresponding DL-SCH data and the state is not settable. Otherwise DCI data contents are indicated sequence with data size and state is settable.
Dependencies	This setting is not visible when State is OFF. When Auto-Configured Bits, State and Data Size are read-only and auto-defined by corresponding DL-SCH.
Preset	ACONfig
State Saved	Yes
Initial S/W Revision	A.20.01

Data User Defined

Sets the DCI payload data for this PDCCH transmission.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:USER<string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:DATA:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:DATa:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:DATa:USER?
Dependencies	This setting is not visible when State is OFF.
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Data Size

Set the payload data size (bits) for DCI.

Seq = 1 to 40

For more details, refer to 3GPP TS 36.212.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:DATA:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:DATA:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:DATA:SIZe 28 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:DATA:SIZe?
Range	1 to 100
Dependencies	This setting is not visible when State is OFF. Where the data is set to Auto-Configured Bits, this parameter is read-only and automatically defined by corresponding DL-SCH.
Preset	28
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RNTI

Sets the RNTI value for this DCI transmission.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:RNTi?
Range	0 to 65535
Dependencies	This setting is not visible when State is OFF. When Data is set to Auto-Configured Bits, this setting is read-only and automatically defined by corresponding DL-SCH. Otherwise, editable.
Preset	1
State Saved	Yes
Min	1
Max	65535
Initial S/W Revision	A.20.01

Search Space

Set the search space for PDCCH.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:SSPace COMMon\|UESPecific [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:SSPace UESPecific RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:SSPace?
Choices	Common \| UE Specific
Dependencies	This setting is not visible when State is OFF. Where RNTI = 65535 (SI-RNTI) and Data = Auto-Configured Bits, this cell is set to Common and is read only. Otherwise, editable.
Preset	UESP
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Aggregation Level

Set the aggregation level for PDCCH.

Seq = 1 to 40

For more details, refer to 3GPP TS 36.211 and 36.213.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:AGGLevel 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:AGGLevel?
Choice	1 \| 2 \| 4 \| 8
Dependencies	This setting is not visible when state is OFF.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Set the PDCCH candidate index.

Seq = 1 to 40

See 3GPP TS 36.211 and 36.213.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:CANDidate?
Range	Depends on Search Space and Aggregation Level: 0 to 5 (UE-Specific, Agg 1/2) 0 to 1 (UE-Specific, Agg 4/8) 0 to 3 (Common, Agg 4) 0 to 1 (Common, Agg 8)
Dependencies	This setting is not visible when State is OFF. When Search Space Auto-Assignment is ON, read-only and automatically assigned from unused lower number.
Preset	0
State Saved	No
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

Query only

Displays the CCE Offset which is automatically calculated by other parameters.

For more details, refer to 3GPP TS 36.213.

Seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:DCI:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DLSCh:DCI:TX:CCE:OFFSet?
Dependencies	This setting is not visible when State is OFF. Automatically calculated from Search Space, Aggregation Level, and Candidate.
Preset	9
State Saved	Yes
Min	0
Max	1023
Initial S/W Revision	A.20.01